105 more things to do!

So, the last time I posted about the DMU, I had been adding plastic rod to the doors.

The construction then moved to the floor and it was exciting to fix a couple of parts to the floor where the bogies are fitted.


My attention then turned to the front of the train and the moulding for the cab. The kit provides a number of variations such as the train code box so if these are not needed you need to carefully remove them with an assortment of files. I was quite anxious about spoiling other areas around the part so I did this with quite a lot of care. As you can see from these pics, there are quite a few variations.

I removed all the unrequired detail leaving me a cab suitable for the middle variant and here it is awaiting the next stage in the process.


The next stage required the removal of some of the rain strip which runs around the top of the cab windows. This is removed so the destination box etch can be fitted. The etch was removed from the fret and I carefully measured the centre of the cab so that I could remove material from the correct part of the cab.

Once the etch was cleaned and ready, I stuck it to the cab using superglue. I use a cocktail stick to apply this on small areas and never use it straight from a bottle so I avoid any disasters.


The next stage was very exciting as I turned my attention to the bogies. This process started by taking the bogie sides and adding the axle bearings. I decided to build the three bogies at this stage leaving the power bogie for another time. Repeating stages can sometimes be a bit tedious but it can also mean that things get done quicker as you get into a pattern and can do things in stages.


I wasn’t a stranger to Easy Build bogies as I had built some for a previous project, however with these being for a DMU I was taking nothing for granted and this was a wise decision given that there were more parts to add on these. The bogies had some further etched brass pieces added on to each end. The decision to buy a folding tool for etched brass kits really paid dividends as this has been used a great deal during the building of the DMU. I can’t imagine how else I would have folded the pieces you see on the next picture.


The bogies then had their axle box covers fitted on with solvent glue suitable for ABS plastic. This is quite smelly so good ventilation is required.

I then added an etched brass mount for the door steps which will be made from plasticard at a future stage.

The instructions suggested fixing the sides, end and cab together in two stages. Unfortunately, I don’t seem to have a picture of this so I’ll sort this when I build the trailer coach. This stage involved adding one side to the back and one side to the cab so that you end up with two L shape parts. Once these are dry, you can glue the two L shaped sections together bringing the cab, two side panels and the rear of the coach together for the first time. This is set aside to dry and harden fully… Now time to build a power bogie!

I have to confess, I was so anxious about building the power bogie, I got engrossed and didn’t take any pictures. I have to say, if there was a stage that was going to put me off any engine kit, it would be the motor part. Despite this, I followed the instructions carefully after reading them a number of times, and all the parts went together really easily and without any pain. I have to say, it was a real pleasure to see my power bogie coming together as this was the first time I had built such a thing. Testing it was really satisfying and I went to bed that night with a big smile on my face.

As the build of the power car progressed, I was able to stick the roof on. I did this after drill holes for the roof vents although these have yet to be fitted. Once the roof was stuck on, it really started to look like a DMU and the model became physically stronger too.

Once the glue on the roof was dry, I decided to add some model filler as the join between the cab and roof needs some attention. The roof and coach end also needs some attention and filling at this stage. I couldn’t quite help myelf and decided to temporarily put the floor and bogies on the body to see what it would look like. It was a good moment!


Next time, I’ll incude pictures of the power bogie and possibly a video testing the power pick ups!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.